Philco 39-7 resto

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 39-7 resto

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#28

01-29-2012, 04:50 PM

Ok pull out the 80 tube and measure the AC voltage across the two smaller pins/ holes at the 80 socket. Should see about 500vac. Be careful stick the two probes in the socket hole and then turn the set on. Did you disconnect the old electrolytic caps when you put in the new ones? If not do so.
CF
Her set had the power transformer replaced and the rectifier was replaced with an 80.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 39-7 resto - by numberdevil - 01-17-2012, 10:21 PM

RE: Philco 39-7 resto - by numberdevil - 11-21-2012, 01:31 AM

RE: Philco 39-7 resto - by 7estatdef - 11-21-2012, 06:00 PM

Re: Philco 39-7 resto - by Dave - 01-18-2012, 09:24 AM

Re: Philco 39-7 resto - by numberdevil - 01-18-2012, 10:06 AM

Re: Philco 39-7 resto - by DKinYORKpa - 01-18-2012, 03:00 PM

Re: Philco 39-7 resto - by numberdevil - 01-18-2012, 04:43 PM

Re: Philco 39-7 resto - by 7estatdef - 01-18-2012, 08:23 PM

Re: Philco 39-7 resto - by numberdevil - 01-19-2012, 09:02 PM

Re: Philco 39-7 resto - by ipwizard - 01-20-2012, 02:25 PM

Re: Philco 39-7 resto - by numberdevil - 01-20-2012, 05:24 PM

Re: Philco 39-7 resto - by 7estatdef - 01-20-2012, 07:29 PM

Re: Philco 39-7 resto - by numberdevil - 01-21-2012, 09:38 PM

Re: Philco 39-7 resto - by 7estatdef - 01-23-2012, 01:56 PM

Re: Philco 39-7 resto - by numberdevil - 01-24-2012, 01:41 AM

Re: Philco 39-7 resto - by 7estatdef - 01-24-2012, 08:26 AM

Re: Philco 39-7 resto - by numberdevil - 01-24-2012, 10:44 AM

Re: Philco 39-7 resto - by 7estatdef - 01-24-2012, 02:49 PM

Re: Philco 39-7 resto - by numberdevil - 01-25-2012, 01:33 AM

Re: Philco 39-7 resto - by numberdevil - 01-27-2012, 01:36 AM

Re: Philco 39-7 resto - by 7estatdef - 01-27-2012, 08:08 AM

Re: Philco 39-7 resto - by numberdevil - 01-27-2012, 09:38 AM

Re: Philco 39-7 resto - by numberdevil - 01-28-2012, 05:22 PM

Re: Philco 39-7 resto - by 7estatdef - 01-28-2012, 07:26 PM

Re: Philco 39-7 resto - by numberdevil - 01-29-2012, 02:48 AM

Re: Philco 39-7 resto - by 7estatdef - 01-29-2012, 10:03 AM

Re: Philco 39-7 resto - by numberdevil - 01-29-2012, 11:58 AM

Re: Philco 39-7 resto - by numberdevil - 01-29-2012, 03:56 PM

Re: Philco 39-7 resto - by codefox1 - 01-29-2012, 04:18 PM

Re: Philco 39-7 resto - by 7estatdef - 01-29-2012, 04:50 PM

Re: Philco 39-7 resto - by numberdevil - 01-29-2012, 07:10 PM

Re: Philco 39-7 resto - by 7estatdef - 01-29-2012, 07:37 PM

Re: Philco 39-7 resto - by numberdevil - 01-30-2012, 10:30 AM

Re: Philco 39-7 resto - by 7estatdef - 01-30-2012, 03:40 PM

Re: Philco 39-7 resto - by codefox1 - 01-30-2012, 05:26 PM

Re: Philco 39-7 resto - by 7estatdef - 01-30-2012, 05:29 PM

Re: Philco 39-7 resto - by codefox1 - 01-30-2012, 06:34 PM

Re: Philco 39-7 resto - by numberdevil - 01-31-2012, 01:20 AM

Re: Philco 39-7 resto - by codefox1 - 01-31-2012, 11:58 AM

Re: Philco 39-7 resto - by numberdevil - 01-31-2012, 07:50 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5740 online users. [Complete List]
» 1 Member(s) | 5739 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me