Zenith 7S363

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith 7S363

LedHed
Rank Amateur

Posts: 83
Threads: 14
Joined: Jan 2012
City: Mount Vernon, WA

02-03-2012, 12:43 AM

Thanks again Jim, I think I saw that on another website. I will make sure I get that cloth next. I am mostly trying to refinish the cabinet more or less in a factory manner. With respect to the original lacquer finish, I don't know if I can do it justice. I will have to do some more research.

One cannot forbid people to be idiots....all one can do is try not to be one. -Morzh

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Zenith 7S363 - by LedHed - 02-01-2012, 09:13 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 02:08 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 03:13 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 03:46 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 05:34 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 05:50 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 06:07 PM

Re: Zenith 7S363 - by Jbaker - 02-02-2012, 10:38 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:14 AM

Re: Zenith 7S363 - by Jbaker - 02-03-2012, 12:27 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:43 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 08:36 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 09:30 AM

Re: Zenith 7S363 - by Eliot Ness - 02-03-2012, 10:08 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 10:27 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 11:41 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 11:44 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:29 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:53 PM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 01:01 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 04:47 PM

Re: Zenith 7S363 - by Jbaker - 02-03-2012, 09:45 PM

Re: Zenith 7S363 - by LedHed - 02-14-2012, 01:30 PM

Re: Zenith 7S363 - by LedHed - 02-14-2012, 01:35 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 723 online users. [Complete List]
» 1 Member(s) | 722 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me