restuffing electrolythics: how do you remove the top cap?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

restuffing electrolythics: how do you remove the top cap?

DeckApe
Senior Member

Posts: 438
Threads: 15
Joined: Jul 2008
City: Anacortes, WA

#10

02-09-2012, 03:17 PM

When re-stuffing an electrolytic, which end is the positive lug? Can, or the rubber-insulated bit in the center? (Or for those of us that have just a snip of trouble following the schematic occasionally...)

Find

« Next Oldest | Next Newest »

Messages In This Thread

restuffing electrolythics: how do you remove the top cap? - by morzh - 02-06-2012, 06:43 PM

Re: restuffing electrolythics: how do you remove the top cap - by 37silverstreak - 02-06-2012, 08:23 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-06-2012, 09:58 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-07-2012, 08:18 PM

Re: restuffing electrolythics: how do you remove the top cap - by codefox1 - 02-08-2012, 11:20 AM

Re: restuffing electrolythics: how do you remove the top cap - by Eliot Ness - 02-08-2012, 12:11 PM

Re: restuffing electrolythics: how do you remove the top cap - by Ron Ramirez - 02-08-2012, 12:18 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-08-2012, 07:28 PM

Re: restuffing electrolythics: how do you remove the top cap - by Ron Ramirez - 02-08-2012, 09:09 PM

Re: restuffing electrolythics: how do you remove the top cap - by DeckApe - 02-09-2012, 03:17 PM

Re: restuffing electrolythics: how do you remove the top cap - by codefox1 - 02-09-2012, 05:16 PM

Re: restuffing electrolythics: how do you remove the top cap - by DeckApe - 02-09-2012, 06:18 PM

Re: restuffing electrolythics: how do you remove the top cap - by Arran - 02-09-2012, 09:28 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-09-2012, 10:01 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-09-2012, 10:03 PM

Re: restuffing electrolythics: how do you remove the top cap - by morzh - 02-10-2012, 02:21 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 7003 online users. [Complete List]
» 2 Member(s) | 7001 Guest(s)