1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Set screw removal
billp
Junior Member
**
Posts: 16
Threads: 5
Joined: Jan 2012
#1

02-12-2012, 04:04 PM
Maybe this is a silly question, but I haven't needed to do this before. The set screws I'm used to dealing with always had a screw slot on the end. These just have a rectangular stub

[Image: http://www.highsierrahosting.com/philco/setscrew.jpg]

Is there a good way/tool to use to back these out? As you can see, access is limited.

-Bill
Time flies like an arrow, fruit flies like a banana
Find
« Next Oldest | Next Newest »


Messages In This Thread
Set screw removal - by billp - 02-12-2012, 04:04 PM
Re: Set screw removal - by Ron Ramirez - 02-12-2012, 07:32 PM
Re: Set screw removal - by codefox1 - 02-13-2012, 04:28 PM
Re: Set screw removal - by Dave - 02-13-2012, 10:11 PM
Re: Set screw removal - by ipwizard - 02-14-2012, 04:44 PM
Re: Set screw removal - by billp - 02-14-2012, 05:26 PM
Re: Set screw removal - by LASJayhawk - 02-14-2012, 07:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 4671 online users. [Complete List]
» 3 Member(s) | 4668 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration