New Project - 39-55

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

New Project - 39-55

codefox1
Silent Key

Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY

#15

02-29-2012, 01:31 AM

Agree with all. I would also wrap as much electrical tape as possible without undue crimping of windings when the bells are tightened up again. BTW scour and spray the inside of the bells as well when you have them off. Also soak the bolts and nuts in oil so you don't bust them when you put it all together again. I think you're all set.

Find

« Next Oldest | Next Newest »

Messages In This Thread

New Project - 39-55 - by ipwizard - 02-28-2012, 04:26 PM

RE: New Project - 39-55 - by codefox1 - 02-28-2012, 04:40 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 04:46 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 04:45 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 05:00 PM

RE: New Project - 39-55 - by Glenn Roberts - 02-28-2012, 05:45 PM

RE: New Project - 39-55 - by Bob Andersen - 02-28-2012, 07:02 PM

RE: New Project - 39-55 - by Ron Ramirez - 02-28-2012, 07:06 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 07:13 PM

RE: New Project - 39-55 - by Ron Ramirez - 02-28-2012, 07:17 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 08:01 PM

RE: New Project - 39-55 - by Ron Ramirez - 02-28-2012, 08:11 PM

RE: New Project - 39-55 - by codefox1 - 02-28-2012, 11:23 PM

RE: New Project - 39-55 - by ipwizard - 02-28-2012, 11:43 PM

RE: New Project - 39-55 - by codefox1 - 02-29-2012, 01:31 AM

RE: New Project - 39-55 - by ipwizard - 03-01-2012, 12:32 AM

RE: New Project - 39-55 - by codefox1 - 03-01-2012, 07:04 AM

RE: New Project - 39-55 - by ipwizard - 03-06-2012, 06:37 PM

RE: New Project - 39-55 - by Arran - 03-06-2012, 09:14 PM

RE: New Project - 39-55 - by ipwizard - 03-06-2012, 07:04 PM

RE: New Project - 39-55 - by ipwizard - 03-06-2012, 11:27 PM

RE: New Project - 39-55 - by Arran - 03-10-2012, 12:52 AM

RE: New Project - 39-55 - by codefox1 - 03-06-2012, 09:34 PM

RE: New Project - 39-55 - by Bob Andersen - 03-07-2012, 12:03 AM

RE: New Project - 39-55 - by ipwizard - 03-07-2012, 12:21 AM

RE: New Project - 39-55 - by ipwizard - 03-07-2012, 01:42 AM

RE: New Project - 39-55 - by Ron Ramirez - 03-11-2012, 08:51 AM

RE: New Project - 39-55 - by ipwizard - 03-10-2012, 11:59 AM

RE: New Project - 39-55 - by Arran - 03-10-2012, 09:15 PM

RE: New Project - 39-55 - by ipwizard - 03-11-2012, 01:45 AM

RE: New Project - 39-55 - by Ron Ramirez - 03-11-2012, 08:38 AM

RE: New Project - 39-55 - by Ron Ramirez - 03-11-2012, 10:51 AM

RE: New Project - 39-55 - by w4rtc - 03-11-2012, 11:03 AM

RE: New Project - 39-55 - by ipwizard - 04-06-2012, 01:04 AM

RE: New Project - 39-55 - by ipwizard - 04-11-2012, 01:10 AM

RE: New Project - 39-55 - by ipwizard - 04-13-2012, 01:47 AM

RE: New Project - 39-55 - by codefox1 - 04-13-2012, 02:11 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me