Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

50-922 Output Tube
#9

The radio has been put back together and I powered it up with a dim bulb tester. It doesn't appear to have any shorts or other obvious problems. When it powered up, it just barely started to put out some audio--just the beginnings of some static, and then went silent. All of the tubes lit up. There's no smoke or hot-smelling components under the chassis. I think it's time to probe around and check voltages to isolate the problem, though I believe it may be another tube that I need to replace. The 50C5 was completely dead and the radio didn't show any signs of life until that one was replaced.

I now have an EICO 666 tube tester, so I'm going to test all of the tubes I didn't replace. However, one of the tubes doesn't show up on any of the EICO tube charts--not even on the latest (1978) version I downloaded from BACA. Anyone out there know how to test a 14B6 on an EICO 666?

--
DeShawn Smith
Current Project: Philco 50-922


Messages In This Thread
50-922 Output Tube - by deshawn - 02-08-2012, 11:24 PM
RE: 50-922 Output Tube - by deshawn - 03-04-2012, 11:41 PM
RE: 50-922 Output Tube - by codefox1 - 03-05-2012, 11:58 AM
RE: 50-922 Output Tube - by deshawn - 03-08-2012, 01:43 PM
Re: 50-922 Output Tube - by codefox1 - 02-09-2012, 11:02 AM
Re: 50-922 Output Tube - by deshawn - 02-09-2012, 11:32 AM
50-922 Missing Capacitor - by deshawn - 02-10-2012, 04:34 PM
Re: 50-922 Output Tube - by Olden Broak - 02-10-2012, 10:56 PM
Re: 50-922 Output Tube - by deshawn - 02-11-2012, 04:26 PM
Re: 50-922 Output Tube - by Ron Ramirez - 02-11-2012, 08:45 PM
Re: 50-922 Output Tube - by deshawn - 02-14-2012, 01:46 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2891 online users. [Complete List]
» 1 Member(s) | 2890 Guest(s)
Avatar

>