1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
50-922 Output Tube
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#10

03-05-2012, 12:58 PM
One wierd set you are working on.

Well pinout is same as 7B6 or 7C6 if you have specs for it, just need to set filament voltage to 12.6. A rewire to the octal world using the readily obtanable 12SQ7 is one workaround should you not be able to find suitable replacement. Also, if the triode section is working ala buzz when you touch the center terminal of the volume control with volume turned up all the way, you can bypass the diode sections with 1N34 diodes. Kind of hard to kill some of these old buggers though.
Find
« Next Oldest | Next Newest »


Messages In This Thread
50-922 Output Tube - by deshawn - 02-09-2012, 12:24 AM
RE: 50-922 Output Tube - by deshawn - 03-05-2012, 12:41 AM
RE: 50-922 Output Tube - by codefox1 - 03-05-2012, 12:58 PM
RE: 50-922 Output Tube - by deshawn - 03-08-2012, 02:43 PM
Re: 50-922 Output Tube - by codefox1 - 02-09-2012, 12:02 PM
Re: 50-922 Output Tube - by deshawn - 02-09-2012, 12:32 PM
50-922 Missing Capacitor - by deshawn - 02-10-2012, 05:34 PM
Re: 50-922 Output Tube - by Olden Broak - 02-10-2012, 11:56 PM
Re: 50-922 Output Tube - by deshawn - 02-11-2012, 05:26 PM
Re: 50-922 Output Tube - by Ron Ramirez - 02-11-2012, 09:45 PM
Re: 50-922 Output Tube - by deshawn - 02-14-2012, 02:46 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 4647 online users. [Complete List]
» 3 Member(s) | 4644 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration