Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco model 20
#3

Hello,

first, sorry for my poor english and I'm new here ;-)

I've bought a Model 20 on ebay and I've got the fourth knob too.

I plan to restart this radio at the end of 2006, I will see what this knob is made for... Probably it's an add-on....

Here it is.

http://cfp.radio.free.fr/dispo/philco%20model%2020.jpg

It's not a heterodyne but a king of TRF receiver.
There's 7 tubes:
2 Rf amplifier with type 24
detection with type 24
type 27 for AF and a push of 2 tube type 71A

It's written philco model 20 on the back, I'm sure of this. but it has 4 knobs

I will have a lot of work on it. There's lot of rust, 2 knobs are missing, the grid cloth (don't known if it's the right word) have a small hole.
The 2 71A are out of order but I've got 2 new one somewhere.

I hope the transformer will be OK, especially the one before the 71A....



best regards
Frederic ABIGNOLI


Messages In This Thread
Philco model 20 - by Guest - 04-18-2006, 10:18 PM
[No subject] - by Chuck Schwark - 04-18-2006, 10:31 PM
[No subject] - by fabignoli - 12-01-2006, 04:57 AM
[No subject] - by Ron Ramirez - 12-01-2006, 09:39 AM
[No subject] - by fabignoli - 12-04-2006, 05:26 AM
[No subject] - by fabignoli - 12-16-2006, 11:31 AM
[No subject] - by Chuck Schwark - 12-16-2006, 04:56 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4302 online users. [Complete List]
» 1 Member(s) | 4301 Guest(s)
Avatar

>