Into the fray with a 116X

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Into the fray with a 116X

LASJayhawk
Senior Member

Posts: 289
Threads: 40
Joined: Oct 2011
City: Las Vegas, NV

03-28-2012, 12:14 AM

If you can handle a 100 pF 200v cap in that application, mouser has their p/n 581-SA102A101JAR (0.19 each) or 80-C410C101J2G (0.58 each) note they are ceramic. They can get 110 pF 400V poly caps at 68 cents each, but it is a long lead time.....And you have to order 3800 of them Icon_sad

If you want radial leads there are a ton o silver micas available at 500V

When I run into this I order a few and some .01 .047 etc for stock so I dont feel to bad about the freight.

John
Las Vegas, NV USA

Find

« Next Oldest | Next Newest »

Messages In This Thread

Into the fray with a 116X - by rocketeer - 03-26-2012, 05:00 PM

RE: Into the fray with a 116X - by TA Forbes - 03-26-2012, 05:32 PM

RE: Into the fray with a 116X - by rocketeer - 03-26-2012, 06:15 PM

RE: Into the fray with a 116X - by rocketeer - 03-27-2012, 09:29 PM

RE: Into the fray with a 116X - by Arran - 03-27-2012, 09:39 PM

RE: Into the fray with a 116X - by rocketeer - 03-27-2012, 11:11 PM

RE: Into the fray with a 116X - by LASJayhawk - 03-28-2012, 12:14 AM

RE: Into the fray with a 116X - by rocketeer - 03-28-2012, 09:11 AM

RE: Into the fray with a 116X - by Chuck Schwark - 03-28-2012, 09:54 AM

RE: Into the fray with a 116X - by rocketeer - 03-28-2012, 08:56 PM

RE: Into the fray with a 116X - by rocketeer - 04-06-2012, 09:32 PM

RE: Into the fray with a 116X - by rocketeer - 04-12-2012, 07:12 PM

RE: Into the fray with a 116X - by TA Forbes - 04-13-2012, 09:47 AM

RE: Into the fray with a 116X - by rocketeer - 04-13-2012, 07:26 PM

RE: Into the fray with a 116X - by Chuck Schwark - 04-13-2012, 09:21 PM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

Who's Online

There are currently 5748 online users. [Complete List]
» 1 Member(s) | 5747 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me