Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Cleaning Philco 90 Volume Control
#21

(04-09-2012, 08:56 PM)morzh Wrote:  Well....none of these potmeters were supposed to be ever opened. It is formally not consider "repairable" part; it is a resistor and it is replaced when going bad.
Some of them had some ways of being cleaned, some did not, but other than spraying "blue shower" in a hole that was it.

But people with some dexterity, of course, can open them up and fix them, if at all possible.

I would say, first, when ready, power it up and see if it works at all. A volume control is not something that is going to kill anything.
Then you will see if you have problems with volume adjusting.

For instance, my potmeter in my 80 Jr. is beyond repair - there is a bald spot, right where the minimum volume should be. No amount of Deoxit will fix that.

I've never heard "potmeter" used as a slang or contraction for "potentiometer" before. Is it regional? Just curious...

Chuck
Icon_biggrin




Messages In This Thread
Cleaning Philco 90 Volume Control - by Sourbone - 03-15-2012, 02:58 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 04-01-2012, 11:28 PM
RE: Cleaning Philco 90 Volume Control - by Arran - 03-16-2012, 08:42 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 03-18-2012, 01:43 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 03-19-2012, 01:56 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 03-21-2012, 06:58 PM
RE: Cleaning Philco 90 Volume Control - by John R - 03-21-2012, 07:46 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 04-03-2012, 10:03 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 04-09-2012, 08:56 PM
RE: Cleaning Philco 90 Volume Control - by Chuck Schwark - 04-09-2012, 09:06 PM
RE: Cleaning Philco 90 Volume Control - by morzh - 04-09-2012, 09:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. S...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM

[-]
Who's Online
There are currently 1372 online users. [Complete List]
» 1 Member(s) | 1371 Guest(s)
Avatar

>