1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 90 Stuck At One Volume Level
Pepperoni
Member
***
Posts: 160
Threads: 42
Joined: Apr 2011
City: New Port Richey State, Province, Country: Florida
#1

04-12-2012, 04:54 PM
I finished the overhaul of this Philco 90 with the single 47 output and it plays but I have no control over the volume. It's just stuck at one volume level and operating the volume control in either direction doesn't change it. VC bench tests good after cleaning. I've gone over all my circuitry and can't find a problem. The only voltage anomally I see is on the plate of the Det. Amp. Paperwork calls out 140 volts and I have 54 volts. But this copy of the paperwork is a little fuzzy. It looks like 140 volts.

I don't know where to look next and could sure use some help.

Thanks,
Pepper
"It's Nice To Be Nice To The Nice"
Major Frank Burns Mash 4077th
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 90 Stuck At One Volume Level - by Pepperoni - 04-12-2012, 04:54 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-12-2012, 10:19 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 03:44 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 03:52 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 07:16 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 09:51 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 01:04 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 02:26 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM

[-]
Who's Online
There are currently 5804 online users. [Complete List]
» 2 Member(s) | 5802 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration