Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

volume Philco 38-116
#2

(05-07-2012, 10:18 PM)murf Wrote:  Been working on this 116 for a while now and have a dumb question.
Re-capped and replaced a bunch of resistors and a few tubes.
It might just be me,but I think that it could do better as far as volume goes.
Everything works fine and it sound good,but I can turn the volume all the way up,without it becoming annoyingly loud and distorted.
My other consoles will get louder than this one.
Have 100 ft single wire antenna on it.This antenna works for the others,so I am thinking it may be something else.
Any clues?
murf

A full alignment is also in order, as well as knowing/checking all the tubes as good before aligning.

With your 100ft. outdoor aerial (and a good ground), you should be able to "wake the neighbors" with that monster.

Chuck


Messages In This Thread
volume Philco 38-116 - by murf - 05-07-2012, 10:18 PM
RE: volume Philco 38-116 - by Chuck Schwark - 05-07-2012, 10:29 PM
RE: volume Philco 38-116 - by murf - 05-07-2012, 10:44 PM
RE: volume Philco 38-116 - by LASJayhawk - 05-08-2012, 12:31 AM
RE: volume Philco 38-116 - by murf - 05-08-2012, 06:52 AM
RE: volume Philco 38-116 - by TA Forbes - 05-08-2012, 10:06 AM
RE: volume Philco 38-116 - by morzh - 05-08-2012, 10:16 AM
RE: volume Philco 38-116 - by codefox1 - 05-08-2012, 10:34 AM
RE: volume Philco 38-116 - by morzh - 05-08-2012, 01:52 PM
RE: volume Philco 38-116 - by murf - 05-08-2012, 04:16 PM
RE: volume Philco 38-116 - by murf - 05-08-2012, 04:32 PM
RE: volume Philco 38-116 - by morzh - 05-08-2012, 04:48 PM
RE: volume Philco 38-116 - by morzh - 05-09-2012, 03:00 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>