Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 48-214 code 125 Cap ?
#8

Yes , one of the tubes dropping low voltage also may do this, though the drop would get distributed. I think the C11 because the radio plays, though all is possible.

BTW, nF is nanofarads. Icon_smile


More, though again not too likely: see if C13A is what it should be and not , say, 300uF.
If I did not know the radio plays, I'd say make sure the filament and the cathode are not shorted, but then the rectifier wouldn't work, and it obviously does, since it plays.

PS. Did not know Philco made "all-american fives".


Messages In This Thread
philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 01:18 PM
RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-20-2012, 02:17 PM
RE: philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 03:10 PM
RE: philco 48-214 code 125 Cap ? - by Arran - 05-20-2012, 09:18 PM
RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 08:37 PM
RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-23-2012, 09:07 PM
RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 09:10 PM
RE: philco 48-214 code 125 Cap ? - by Arran - 05-23-2012, 11:25 PM
RE: philco 48-214 code 125 Cap ? - by morzh - 05-24-2012, 09:28 AM
RE: philco 48-214 code 125 Cap ? - by Eric - 05-24-2012, 03:14 PM
RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-24-2012, 10:13 PM
RE: philco 48-214 code 125 Cap ? - by Eric - 05-29-2012, 03:08 PM
RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-30-2012, 07:15 AM
RE: philco 48-214 code 125 Cap ? - by morzh - 05-30-2012, 08:25 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 3475 online users. [Complete List]
» 5 Member(s) | 3470 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>