1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38 116 low volume after recapp
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

06-07-2012, 05:12 PM
+1 on the latest response. I will attach a link to the schematic for others. Should you be able to post a picture, I would love a close up of your tuning dial. I have a friend who is missing a part. Like to see what it is. I too may be working on one in the future. Good luck. See my post here on a 116.

Jerry

http://www.nostalgiaair.org/PagesByModel...013234.pdf
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »


Messages In This Thread
38 116 low volume after recapp - by SteveJB - 06-07-2012, 03:03 PM
RE: 38 116 low volume after recapp - by rghines1 - 06-07-2012, 03:58 PM
RE: 38 116 low volume after recapp - by jerryhawthorne - 06-07-2012, 05:12 PM
RE: 38 116 low volume after recapp - by 7estatdef - 06-07-2012, 09:14 PM
RE: 38 116 low volume after recapp - by SteveJB - 06-07-2012, 09:42 PM
RE: 38 116 low volume after recapp - by 7estatdef - 06-08-2012, 06:54 AM
RE: 38 116 low volume after recapp - by SteveJB - 06-08-2012, 10:17 AM
RE: 38 116 low volume after recapp - by codefox1 - 06-08-2012, 11:09 AM
RE: 38 116 low volume after recapp - by SteveJB - 06-08-2012, 11:34 AM
RE: 38 116 low volume after recapp - by rghines1 - 06-08-2012, 04:41 PM
RE: 38 116 low volume after recapp - by SteveJB - 07-17-2012, 06:39 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4774 online users. [Complete List]
» 2 Member(s) | 4772 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration