1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-150 issues
morzh
Odobenus rosmarus
*****
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
#2

06-16-2012, 11:37 AM
If you read the voltages with the 41s out they will be higher.
Now, 1) check the field coil of the sleaker, see if it is 1k or it is in fact lower, much lower or downright shorted. 2) Cap 61 is 12uF as required, not 20uF or so. 3) Xfmr input windings read 210 and 240 Ohms or close, no much lower, or open. 4) caps 55A/B are ok and not shorted.
(This post was last modified: 06-16-2012, 11:38 AM by morzh.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
40-150 issues - by RGallahue - 06-16-2012, 10:20 AM
RE: 40-150 issues - by morzh - 06-16-2012, 11:37 AM
RE: 40-150 issues - by RGallahue - 06-16-2012, 01:32 PM
RE: 40-150 issues - by morzh - 06-16-2012, 03:02 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 05:04 PM
RE: 40-150 issues - by 7estatdef - 06-16-2012, 05:34 PM
RE: 40-150 issues - by morzh - 06-16-2012, 06:53 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 07:15 PM
RE: 40-150 issues - by morzh - 06-16-2012, 07:31 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 08:34 PM
RE: 40-150 issues - by morzh - 06-16-2012, 10:05 PM
RE: 40-150 issues - by RGallahue - 06-17-2012, 09:38 AM
RE: 40-150 issues - by morzh - 06-17-2012, 10:27 AM
RE: 40-150 issues - by RGallahue - 06-17-2012, 10:46 AM
RE: 40-150 issues - by morzh - 06-17-2012, 12:47 PM
RE: 40-150 issues - by 7estatdef - 06-17-2012, 01:24 PM
RE: 40-150 issues - by RGallahue - 06-19-2012, 07:12 PM
RE: 40-150 issues - by morzh - 06-20-2012, 04:45 PM
RE: 40-150 issues - by RGallahue - 06-20-2012, 05:16 PM
RE: 40-150 issues - by morzh - 06-21-2012, 09:51 PM
RE: 40-150 issues - by morzh - 06-23-2012, 12:21 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently 5357 online users. [Complete List]
» 2 Member(s) | 5355 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration