1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 37-84 Photo Finish Help
gpitt1960
Junior Member
**
Posts: 8
Threads: 2
Joined: Jun 2012
City: Tuscumbia, AL / Rock Hill, SC
#1

06-16-2012, 01:04 PM
I am a restorer of chassis and not the cabinets, what is the recomendation from this forum in regards to refinishing this cabinet, It is solid all over, even the tube layout paper diagram and warranty tag inside. I have researched the Philco pages and read the article from the deceased gentleman concerning the use of a black and white photo copy and then pigmenting the paper to emulate the photo finish. Is there any members out there that has mass produced the photo finish for the 37-84. I believe that I would be better off leaving it in it's current condition than to simply strip and generically finish the front, Please advise,

Greg


Attached Files Image(s)
       
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 37-84 Photo Finish Help - by gpitt1960 - 06-16-2012, 01:04 PM
RE: Philco 37-84 Photo Finish Help - by codefox1 - 06-16-2012, 02:45 PM
RE: Philco 37-84 Photo Finish Help - by 7estatdef - 06-16-2012, 06:50 PM
RE: Philco 37-84 Photo Finish Help - by TA Forbes - 06-16-2012, 10:47 PM
RE: Philco 37-84 Photo Finish Help - by codefox1 - 06-17-2012, 03:21 AM
RE: Philco 37-84 Photo Finish Help - by gpitt1960 - 06-17-2012, 11:59 AM
RE: Philco 37-84 Photo Finish Help - by gpitt1960 - 06-17-2012, 12:21 PM
RE: Philco 37-84 Photo Finish Help - by 7estatdef - 06-17-2012, 02:12 PM
RE: Philco 37-84 Photo Finish Help - by codefox1 - 06-17-2012, 04:00 PM
RE: Philco 37-84 Photo Finish Help - by gpitt1960 - 06-17-2012, 08:56 PM
RE: Philco 37-84 Photo Finish Help - by gpitt1960 - 06-18-2012, 01:14 PM
RE: Philco 37-84 Photo Finish Help - by 7estatdef - 06-18-2012, 02:34 PM
RE: Philco 37-84 Photo Finish Help - by gpitt1960 - 06-26-2012, 07:45 PM
RE: Philco 37-84 Photo Finish Help - by 7estatdef - 06-26-2012, 10:03 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 6129 online users. [Complete List]
» 2 Member(s) | 6127 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration