Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-150 issues
#12

I was looking at the last test you spoke of, that being connecting the lamp in series with the primary ends of the transformer. However, is there not continuity between the primary ends? In other words, wouldn't the lamp glow regardless of the state of the secondary (open or shorted)? If I measure resistance across both halves, it is the additive resistance of the two sections above (316 ohms).

Sorry for all of the questions, I just want to understand the testing procedure. If I indeed had the turns ratio, this probably would be simpler as I could test for the ratio of voltages.

And I really do appreciate all of the help.

Richard

Richard


Messages In This Thread
40-150 issues - by RGallahue - 06-16-2012, 11:20 AM
RE: 40-150 issues - by morzh - 06-16-2012, 12:37 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 02:32 PM
RE: 40-150 issues - by morzh - 06-16-2012, 04:02 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 06:04 PM
RE: 40-150 issues - by 7estatdef - 06-16-2012, 06:34 PM
RE: 40-150 issues - by morzh - 06-16-2012, 07:53 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 08:15 PM
RE: 40-150 issues - by morzh - 06-16-2012, 08:31 PM
RE: 40-150 issues - by RGallahue - 06-16-2012, 09:34 PM
RE: 40-150 issues - by morzh - 06-16-2012, 11:05 PM
RE: 40-150 issues - by RGallahue - 06-17-2012, 10:38 AM
RE: 40-150 issues - by morzh - 06-17-2012, 11:27 AM
RE: 40-150 issues - by RGallahue - 06-17-2012, 11:46 AM
RE: 40-150 issues - by morzh - 06-17-2012, 01:47 PM
RE: 40-150 issues - by 7estatdef - 06-17-2012, 02:24 PM
RE: 40-150 issues - by RGallahue - 06-19-2012, 08:12 PM
RE: 40-150 issues - by morzh - 06-20-2012, 05:45 PM
RE: 40-150 issues - by RGallahue - 06-20-2012, 06:16 PM
RE: 40-150 issues - by morzh - 06-21-2012, 10:51 PM
RE: 40-150 issues - by morzh - 06-23-2012, 01:21 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
A Marconi model 86
I have recapped this large Marconi model 86.  It plays quit good.         I have stripped the cabinet and using Mohawk...Dan Walker — 12:18 AM
Table radio 51C or 52C?
I think what you may have is another Phactory Phranken Philco, if the holes in the front panel lined up it was not unusu...Arran — 10:41 PM
Philco 42-345 Restoration/Repair
Ho OSanders, Sorry, I got really busy in May and haven't seen your thread in a while.  I am VERY sorry about that.  ...MrFixr55 — 10:30 PM
Philco 45L Initial Check Up
Dan; I don't think that the model 45 is especially know for coil problems, not that they can't occur for one reason o...Arran — 10:19 PM
Philco 42-345 Restoration/Repair
Yes, the end with the groove is positive, the stripe with the arrows points to the negative lead. The arrows have minus ...RodB — 09:36 PM
Philco 42-345 Restoration/Repair
Thank you Rod and Paul I took a break, did some yard work and Rod "Therefore, it appears cap 40 is connected backw...osanders0311 — 06:35 PM
Philco 45L Initial Check Up
Hello, I am in the process of checking out a Philco 45L. My question is does this model suffer from the Philco coil r...dconant — 06:11 PM
Table radio 51C or 52C?
Purchased a table radio at auction, not because I had to have it, but because no one else bid on it.  $5  Unable to fi...antiqueradionut — 05:14 PM
Philco 42-345 Restoration/Repair
The 2 towns you mentioned "Frustrated" and "Give Up" are places we have all been. Relax, take 5, thi...Paul Philco322 — 03:23 PM
Philco 89 Code 123 Osc Coil
Thanks for posting that information!klondike98 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>