Next project-another 66!

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Next project-another 66!

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

07-05-2012, 06:08 PM

After following Steve's suggestions I would change the .002 in the tone control to .005 or so. That should take care of the squeal problem. It's sounds like the volume control is bad I'd replace it.
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Next project-another 66! - by jph14 - 07-05-2012, 02:55 PM

RE: Next project-another 66! - by Steve Davis - 07-05-2012, 04:49 PM

RE: Next project-another 66! - by 7estatdef - 07-05-2012, 06:08 PM

RE: Next project-another 66! - by morzh - 07-05-2012, 08:25 PM

RE: Next project-another 66! - by TA Forbes - 07-06-2012, 01:18 PM

RE: Next project-another 66! - by codefox1 - 07-06-2012, 04:36 PM

RE: Next project-another 66! - by jph14 - 07-06-2012, 06:46 PM

RE: Next project-another 66! - by 7estatdef - 07-06-2012, 07:35 PM

RE: Next project-another 66! - by morzh - 07-06-2012, 07:46 PM

RE: Next project-another 66! - by jph14 - 07-09-2012, 05:26 PM

RE: Next project-another 66! - by jph14 - 07-26-2012, 02:22 PM

RE: Next project-another 66! - by 7estatdef - 07-26-2012, 07:57 PM

RE: Next project-another 66! - by jerryhawthorne - 07-28-2012, 07:00 PM

RE: Next project-another 66! - by jph14 - 08-09-2012, 05:26 PM

RE: Next project-another 66! - by 7estatdef - 08-09-2012, 06:59 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4917 online users. [Complete List]
» 2 Member(s) | 4915 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me