Another Zenith 9-S-262 thread

Thread Rating:

1 Vote(s) - 5 Average
1
2
3
4
5

Linear Mode

Another Zenith 9-S-262 thread

rocketeer
Senior Member

Posts: 462
Threads: 40
Joined: Jun 2010
City: Lehighton State, Province, Country: PA

07-06-2012, 04:36 PM

Still doing veneer repairs. This has been mentioned before but a good way to clamp down veneers on a curve is to use a cheap web belt tie down. Work the glue under the lifted veneer, press it down and squeeze out the extra then wipe it away, lay a piece of wax paper over it and strap it down with a web belt (ratchet type) tie down. Be careful not to over-tighten, an easy thing to do.

[Image: http://i863.photobucket.com/albums/ab191...262-40.jpg]

Larry

(This post was last modified: 07-06-2012, 04:37 PM by rocketeer.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Another Zenith 9-S-262 thread - by rocketeer - 06-20-2012, 09:49 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 06-24-2012, 11:01 AM

RE: Another Zenith 9-S-262 thread - by Eliot Ness - 06-24-2012, 11:04 PM

RE: Another Zenith 9-S-262 thread - by Dan Walker - 06-25-2012, 09:39 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 07-06-2012, 04:36 PM

RE: Another Zenith 9-S-262 thread - by DeckApe - 07-06-2012, 06:15 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 07-06-2012, 07:38 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 07-18-2012, 04:13 PM

RE: Another Zenith 9-S-262 thread - by morzh - 07-18-2012, 08:50 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 07-19-2012, 11:12 AM

RE: Another Zenith 9-S-262 thread - by morzh - 07-19-2012, 02:37 PM

RE: Another Zenith 9-S-262 thread - by codefox1 - 07-19-2012, 07:38 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 07-21-2012, 04:12 PM

RE: Another Zenith 9-S-262 thread - by Geoff - 07-21-2012, 06:23 PM

RE: Another Zenith 9-S-262 thread - by rocketeer - 08-16-2012, 06:47 PM

RE: Another Zenith 9-S-262 thread - by Ron Ramirez - 06-02-2013, 08:45 AM

RE: Another Zenith 9-S-262 thread - by rocketeer - 06-05-2013, 12:02 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4717 online users. [Complete List]
» 1 Member(s) | 4716 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me