1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Next project-another 66!
jph14
Member
***
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
#7

07-06-2012, 06:46 PM
Thanks guys.
Steve- checked shields and grid wire== all good.
Terry- will change .002 to .005.
Any thoughts on where to track down a 350,000 ohm vol. control? I have 250,000 and 500,000 ohm vol. controls in stock. Will either of these help?
Joe
Find
« Next Oldest | Next Newest »


Messages In This Thread
Next project-another 66! - by jph14 - 07-05-2012, 02:55 PM
RE: Next project-another 66! - by Steve Davis - 07-05-2012, 04:49 PM
RE: Next project-another 66! - by 7estatdef - 07-05-2012, 06:08 PM
RE: Next project-another 66! - by morzh - 07-05-2012, 08:25 PM
RE: Next project-another 66! - by TA Forbes - 07-06-2012, 01:18 PM
RE: Next project-another 66! - by codefox1 - 07-06-2012, 04:36 PM
RE: Next project-another 66! - by jph14 - 07-06-2012, 06:46 PM
RE: Next project-another 66! - by 7estatdef - 07-06-2012, 07:35 PM
RE: Next project-another 66! - by morzh - 07-06-2012, 07:46 PM
RE: Next project-another 66! - by jph14 - 07-09-2012, 05:26 PM
RE: Next project-another 66! - by jph14 - 07-26-2012, 02:22 PM
RE: Next project-another 66! - by 7estatdef - 07-26-2012, 07:57 PM
RE: Next project-another 66! - by jerryhawthorne - 07-28-2012, 07:00 PM
RE: Next project-another 66! - by jph14 - 08-09-2012, 05:26 PM
RE: Next project-another 66! - by 7estatdef - 08-09-2012, 06:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4766 online users. [Complete List]
» 2 Member(s) | 4764 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration