Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Pilot Lamp Source?
#8

Funny you should mention that, Mars. I've been thinking about trying some of those LED replacements. Have you tried any of them, and if so, do you like how they look?

Another benefit they have is lower power consumption - they draw less current. When we are dealing with very old power transformers, anything that will lower current draw is a good thing, I think.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Pilot Lamp Source? - by lyle - 07-13-2012, 12:50 PM
RE: Pilot Lamp Source? - by Carl Travis - 07-13-2012, 01:50 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-13-2012, 04:31 PM
RE: Pilot Lamp Source? - by lyle - 07-13-2012, 05:52 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-13-2012, 06:14 PM
RE: Pilot Lamp Source? - by lyle - 07-13-2012, 06:51 PM
RE: Pilot Lamp Source? - by Marsupial - 07-13-2012, 11:31 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-14-2012, 05:42 AM
RE: Pilot Lamp Source? - by exray - 07-14-2012, 09:43 AM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-14-2012, 10:07 AM
RE: Pilot Lamp Source? - by Glenn Roberts - 07-14-2012, 10:16 AM
RE: Pilot Lamp Source? - by morzh - 07-14-2012, 11:56 AM
RE: Pilot Lamp Source? - by Marsupial - 07-14-2012, 08:32 PM
RE: Pilot Lamp Source? - by lyle - 07-19-2012, 08:51 AM
RE: Pilot Lamp Source? - by Eliot Ness - 07-19-2012, 12:25 PM
RE: Pilot Lamp Source? - by Marsupial - 07-19-2012, 10:59 PM
RE: Pilot Lamp Source? - by Eliot Ness - 07-21-2012, 10:16 AM
RE: Pilot Lamp Source? - by Marsupial - 07-21-2012, 08:24 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5786 online users. [Complete List]
» 1 Member(s) | 5785 Guest(s)
Avatar

>