1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Pilot Lamp Source?
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#10

07-14-2012, 10:07 AM
Bill (exray) is absolutely right! I was thinking about their use in AC-only (with a power transformer) sets.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Pilot Lamp Source? - by lyle - 07-13-2012, 12:50 PM
RE: Pilot Lamp Source? - by Carl Travis - 07-13-2012, 01:50 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-13-2012, 04:31 PM
RE: Pilot Lamp Source? - by lyle - 07-13-2012, 05:52 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-13-2012, 06:14 PM
RE: Pilot Lamp Source? - by lyle - 07-13-2012, 06:51 PM
RE: Pilot Lamp Source? - by Marsupial - 07-13-2012, 11:31 PM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-14-2012, 05:42 AM
RE: Pilot Lamp Source? - by exray - 07-14-2012, 09:43 AM
RE: Pilot Lamp Source? - by Ron Ramirez - 07-14-2012, 10:07 AM
RE: Pilot Lamp Source? - by Glenn Roberts - 07-14-2012, 10:16 AM
RE: Pilot Lamp Source? - by morzh - 07-14-2012, 11:56 AM
RE: Pilot Lamp Source? - by Marsupial - 07-14-2012, 08:32 PM
RE: Pilot Lamp Source? - by lyle - 07-19-2012, 08:51 AM
RE: Pilot Lamp Source? - by Eliot Ness - 07-19-2012, 12:25 PM
RE: Pilot Lamp Source? - by Marsupial - 07-19-2012, 10:59 PM
RE: Pilot Lamp Source? - by Eliot Ness - 07-21-2012, 10:16 AM
RE: Pilot Lamp Source? - by Marsupial - 07-21-2012, 08:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6090 online users. [Complete List]
» 2 Member(s) | 6088 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration