Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

WHICH 690 IS BEST BET?
#19

WOW Sam your a busy guy, and what great consoles your adding to your collection. I am jelous. Good luck with all of them hope you post pictures when you get them for all of us to see!


Messages In This Thread
WHICH 690 IS BEST BET? - by Sam samuelian - 06-13-2012, 06:31 AM
RE: WHICH 690 IS BEST BET? - by codefox1 - 06-13-2012, 01:01 PM
RE: WHICH 690 IS BEST BET? - by Ron Ramirez - 06-13-2012, 03:41 PM
RE: WHICH 690 IS BEST BET? - by Sam samuelian - 06-13-2012, 03:50 PM
RE: WHICH 690 IS BEST BET? - by TA Forbes - 06-13-2012, 08:32 PM
RE: WHICH 690 IS BEST BET? - by Arran - 06-13-2012, 11:57 PM
RE: WHICH 690 IS BEST BET? - by 7estatdef - 06-14-2012, 02:59 PM
RE: WHICH 690 IS BEST BET? - by Ron Ramirez - 06-14-2012, 07:45 PM
RE: WHICH 690 IS BEST BET? - by Arran - 06-14-2012, 08:41 PM
RE: WHICH 690 IS BEST BET? - by TA Forbes - 06-15-2012, 06:51 PM
RE: WHICH 690 IS BEST BET? - by Jayce - 06-15-2012, 07:00 PM
RE: WHICH 690 IS BEST BET? - by TA Forbes - 06-15-2012, 08:35 PM
RE: WHICH 690 IS BEST BET? - by Arran - 06-16-2012, 02:01 AM
RE: WHICH 690 IS BEST BET? - by Jayce - 06-16-2012, 02:44 PM
RE: WHICH 690 IS BEST BET? - by codefox1 - 06-16-2012, 10:41 PM
RE: WHICH 690 IS BEST BET? - by Sam samuelian - 06-19-2012, 12:09 PM
RE: WHICH 690 IS BEST BET? - by Ron Ramirez - 06-20-2012, 04:40 AM
RE: WHICH 690 IS BEST BET? - by Sam samuelian - 07-20-2012, 03:45 AM
RE: WHICH 690 IS BEST BET? - by PhilcoJohn - 07-20-2012, 06:10 PM
RE: WHICH 690 IS BEST BET? - by Ron Ramirez - 07-20-2012, 09:26 PM
RE: WHICH 690 IS BEST BET? - by Arran - 07-21-2012, 10:11 PM
RE: WHICH 690 IS BEST BET? - by Arran - 07-22-2012, 06:22 AM
RE: WHICH 690 IS BEST BET? - by Ron Ramirez - 07-22-2012, 07:14 AM
RE: WHICH 690 IS BEST BET? - by TA Forbes - 07-22-2012, 09:56 AM
RE: WHICH 690 IS BEST BET? - by Arran - 07-22-2012, 09:51 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 4751 online users. [Complete List]
» 2 Member(s) | 4749 Guest(s)
AvatarAvatar

>