Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Starting on Philco 111 More Questions & Pics
#6

I'll bet half of those resistors are open, the ones with the pointy ends. The dog bones will have drifted up X2 or more. If you take them out, don't throw them away.

I cant tell what the extra thing is in the picture, probably a cap replacement. There are supposed to be 3 resistors under there.


Messages In This Thread
RE: Starting on Philco 111 - by Ron Ramirez - 08-14-2012, 05:41 AM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 10:01 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 02:45 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 03:58 PM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 05:54 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 08:19 PM
RE: Starting on Philco 111 - by Chuck Schwark - 08-14-2012, 10:23 PM
RE: Starting on Philco 111 - by codefox1 - 08-14-2012, 11:41 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 01:02 AM
RE: Starting on Philco 111 - by Chuck Schwark - 08-15-2012, 09:20 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 02:59 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 07:01 PM
RE: Starting on Philco 111 - by 7estatdef - 08-17-2012, 07:28 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 08:20 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 10:31 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 11:30 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-18-2012, 09:37 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-19-2012, 10:25 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-20-2012, 07:28 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-21-2012, 01:01 AM
RE: Starting on Philco 111 - by 7estatdef - 08-21-2012, 08:05 AM
RE: Starting on Philco 111 - by TA Forbes - 08-21-2012, 11:26 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-22-2012, 02:57 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 04:34 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 11:28 PM
RE: Starting on Philco 111 - by codefox1 - 08-25-2012, 11:42 AM
RE: Starting on Philco 111 - by TA Forbes - 08-27-2012, 02:17 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-28-2012, 05:06 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4930 online users. [Complete List]
» 2 Member(s) | 4928 Guest(s)
AvatarAvatar

>