Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Starting on Philco 111 More Questions & Pics
#33

Your test says it all. Somewhere vic the 1stDet/Osc circuit. Check coils for continuity, I don't see where the resistance values are listed.
Also could be something making contact that is not supposed to.
Are the tube sockets OK? Not corroded, dirty, bent, etc...
Although I have never heard of one, could it be a "noisy" 24/27 tube?

Next would be the mica caps.


Messages In This Thread
RE: Starting on Philco 111 - by Ron Ramirez - 08-14-2012, 05:41 AM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 10:01 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 02:45 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 03:58 PM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 05:54 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 08:19 PM
RE: Starting on Philco 111 - by Chuck Schwark - 08-14-2012, 10:23 PM
RE: Starting on Philco 111 - by codefox1 - 08-14-2012, 11:41 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 01:02 AM
RE: Starting on Philco 111 - by Chuck Schwark - 08-15-2012, 09:20 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 02:59 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 07:01 PM
RE: Starting on Philco 111 - by 7estatdef - 08-17-2012, 07:28 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 08:20 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 10:31 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 11:30 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-18-2012, 09:37 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-19-2012, 10:25 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-20-2012, 07:28 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-21-2012, 01:01 AM
RE: Starting on Philco 111 - by 7estatdef - 08-21-2012, 08:05 AM
RE: Starting on Philco 111 - by TA Forbes - 08-21-2012, 11:26 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-22-2012, 02:57 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 04:34 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 11:28 PM
RE: Starting on Philco 111 - by codefox1 - 08-25-2012, 11:42 AM
RE: Starting on Philco 111 - by TA Forbes - 08-27-2012, 02:17 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-28-2012, 05:06 PM
RE: Starting on Philco 111 More Questions & Pics - by TA Forbes - 08-28-2012, 11:58 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4808 online users. [Complete List]
» 1 Member(s) | 4807 Guest(s)
Avatar

>