Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tube question
#10

Eric, here is quick and dirty troubleshooting procedure. First, holding a capacitor (value not critical .01 or so would be good) in your fingers by one lead, touch the other lead to the center terminal (the wiper) of the volume control. You should hear a hum in the speaker. If so, the audio section is working, at least in some fashion. Next, tune the radio to mid band, say 800kc. Now take a portable radio tuned to 1255 (800 + 455) and place it near your Emerson. Now rock the tuning slightly on either one of the radios. The portable should pick up the local oscillator of the radio under test. By doing these two test, you will prove (or disprove) about 2/3 of the radio circuit.

Steve

M R Radios   C M Tubes


Messages In This Thread
Tube question - by Eric - 08-27-2012, 04:26 PM
RE: Tube question - by rghines1 - 08-27-2012, 06:37 PM
RE: Tube question - by Eric - 08-27-2012, 07:21 PM
RE: Tube question - by Arran - 08-28-2012, 12:02 AM
RE: Tube question - by Eric - 08-28-2012, 11:15 AM
RE: Tube question - by codefox1 - 08-28-2012, 01:12 PM
RE: Tube question - by Eric - 08-28-2012, 03:05 PM
RE: Tube question - by Arran - 08-29-2012, 06:46 PM
RE: Tube question - by Eric - 09-01-2012, 09:47 PM
RE: Tube question - by Steve Davis - 09-02-2012, 01:31 PM
RE: Tube question - by Eric - 09-03-2012, 09:00 AM
RE: Tube question - by 7estatdef - 09-03-2012, 03:47 PM
RE: Tube question - by Eric - 09-04-2012, 02:44 PM
RE: Tube question - by 7estatdef - 09-04-2012, 04:26 PM
RE: Tube question - by Eric - 09-06-2012, 12:20 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>