started (at last) to refinish my 47-1230

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

started (at last) to refinish my 47-1230

Marsupial
Senior Member

Posts: 336
Threads: 13
Joined: Apr 2011
City: Montreal, Qc

#12

09-05-2012, 09:42 AM

So, the first layer is of a different material. What do I need to look for when I get to the hardware store?

Sorry I am a total noobie at that, but thanks to you guys, I'm learning Icon_biggrin

-Mars

Find

« Next Oldest | Next Newest »

Messages In This Thread

started (at last) to refinish my 47-1230 - by Marsupial - 09-02-2012, 08:39 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-03-2012, 01:03 PM

RE: started (at last) to refinish my 47-1230 - by Arran - 09-03-2012, 07:28 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-03-2012, 11:47 PM

RE: started (at last) to refinish my 47-1230 - by Ron Ramirez - 09-04-2012, 08:56 AM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-04-2012, 09:29 AM

RE: started (at last) to refinish my 47-1230 - by Ron Ramirez - 09-04-2012, 09:39 AM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-04-2012, 10:33 AM

RE: started (at last) to refinish my 47-1230 - by Arran - 09-04-2012, 04:51 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-04-2012, 07:12 PM

RE: started (at last) to refinish my 47-1230 - by Steve Davis - 09-04-2012, 08:30 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-05-2012, 09:42 AM

RE: started (at last) to refinish my 47-1230 - by Steve Davis - 09-05-2012, 12:22 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-05-2012, 02:30 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-07-2012, 09:28 AM

RE: started (at last) to refinish my 47-1230 - by Bob Andersen - 09-07-2012, 05:59 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-07-2012, 08:52 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-07-2012, 09:05 PM

RE: started (at last) to refinish my 47-1230 - by Arran - 09-07-2012, 11:41 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-08-2012, 09:28 AM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-08-2012, 10:03 AM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-08-2012, 02:22 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 09-09-2012, 06:45 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 10-21-2012, 03:54 PM

RE: started (at last) to refinish my 47-1230 - by NostalgiaRadioTime - 10-21-2012, 07:21 PM

RE: started (at last) to refinish my 47-1230 - by Marsupial - 10-21-2012, 08:14 PM

View a Printable Version

Users browsing this thread: 13 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me