Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Starting on Philco 111 More Questions & Pics
#63

Jerry,

Apparently my 111 is missing the shield that you mention. I take it that it goes across the back shielding the 224s kind of like in a 70 or 90? Do you have a picture?

Here is a picture of mine - sorry, cell phone does not know what focus means. It does work great though with just a 4 ft chunk of wire for an antenna. It is a keeper.


   

   


Messages In This Thread
RE: Starting on Philco 111 - by Ron Ramirez - 08-14-2012, 05:41 AM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 10:01 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 02:45 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 03:58 PM
RE: Starting on Philco 111 - by Phlogiston - 08-14-2012, 05:54 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-14-2012, 08:19 PM
RE: Starting on Philco 111 - by Chuck Schwark - 08-14-2012, 10:23 PM
RE: Starting on Philco 111 - by codefox1 - 08-14-2012, 11:41 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 01:02 AM
RE: Starting on Philco 111 - by Chuck Schwark - 08-15-2012, 09:20 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-15-2012, 02:59 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 07:01 PM
RE: Starting on Philco 111 - by 7estatdef - 08-17-2012, 07:28 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 08:20 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-17-2012, 10:31 PM
RE: Starting on Philco 111 - by Phlogiston - 08-17-2012, 11:30 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-18-2012, 09:37 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-19-2012, 10:25 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-20-2012, 07:28 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-21-2012, 01:01 AM
RE: Starting on Philco 111 - by 7estatdef - 08-21-2012, 08:05 AM
RE: Starting on Philco 111 - by TA Forbes - 08-21-2012, 11:26 AM
RE: Starting on Philco 111 - by jerryhawthorne - 08-22-2012, 02:57 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 04:34 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-24-2012, 11:28 PM
RE: Starting on Philco 111 - by codefox1 - 08-25-2012, 11:42 AM
RE: Starting on Philco 111 - by TA Forbes - 08-27-2012, 02:17 PM
RE: Starting on Philco 111 - by jerryhawthorne - 08-28-2012, 05:06 PM
RE: Starting on Philco 111 More Questions & Pics - by Phlogiston - 09-19-2012, 01:33 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 5062 online users. [Complete List]
» 1 Member(s) | 5061 Guest(s)
Avatar

>