I've done it again!

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

I've done it again!

jerryhawthorne
Phorum Expert

Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA

#19

09-19-2012, 10:55 PM

Your right TA, Aaron has a lot more electronic experience than me. Certainly no offence to him but he can be a bit negative. Just saying for the age and the quality, Ron is going to have one heck of a radio if he finds all the parts. I'm a Scott fan, next Philco, their easier to afford and I like them. Heck, look at all the rusty chassis many of us buy and clean them up. I did have a bit of chroming done on my Metro. Really expensive, wish I owned a chrome shop.
Jerry

A friend in need is a pest! Bill Slee ca 1970.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

I've done it again! - by Ron Ramirez - 08-07-2012, 06:07 PM

RE: I've done it again! - by codefox1 - 08-07-2012, 06:37 PM

RE: I've done it again! - by ipwizard - 08-07-2012, 06:37 PM

RE: I've done it again! - by w4rtc - 08-07-2012, 08:59 PM

RE: I've done it again! - by TA Forbes - 08-08-2012, 12:19 AM

RE: I've done it again! - by Ron Ramirez - 08-09-2012, 05:48 AM

RE: I've done it again! - by Glenn Roberts - 08-09-2012, 01:06 PM

RE: I've done it again! - by Ron Ramirez - 09-15-2012, 08:15 PM

RE: I've done it again! - by Michael Dennis - 09-15-2012, 08:59 PM

RE: I've done it again! - by Eliot Ness - 09-15-2012, 09:30 PM

RE: I've done it again! - by Michael Dennis - 09-15-2012, 09:43 PM

RE: I've done it again! - by codefox1 - 09-16-2012, 03:45 AM

RE: I've done it again! - by TA Forbes - 09-16-2012, 02:28 PM

RE: I've done it again! - by Ron Ramirez - 09-16-2012, 08:05 PM

RE: I've done it again! - by Arran - 09-16-2012, 08:48 PM

RE: I've done it again! - by TA Forbes - 09-17-2012, 09:17 AM

RE: I've done it again! - by jerryhawthorne - 09-19-2012, 09:38 PM

RE: I've done it again! - by TA Forbes - 09-19-2012, 10:18 PM

RE: I've done it again! - by jerryhawthorne - 09-19-2012, 10:55 PM

RE: I've done it again! - by TA Forbes - 09-19-2012, 11:05 PM

RE: I've done it again! - by jerryhawthorne - 09-19-2012, 11:27 PM

RE: I've done it again! - by Arran - 09-20-2012, 01:18 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM
Philco 610B oscillator wiring
Regarding the oscillator circuit which is comprised of the 6A7's cathode, control grid, and screen grid. These elements ...Radioroslyn — 10:33 AM
Philco 42-345 Restoration/Repair
Hi OSanders, First off, welcome to the Philco Phorum where Phine Phamily-Phriendly Pholks Phull of Philco Phacts and P...MrFixr55 — 08:41 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me