Trouble getting started

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Trouble getting started

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

09-30-2012, 01:05 AM

No, Jerry,

The caps are in and it passed the dim bulb test, but no sound. I bought a tube tester and should have it Monday. I'm sure that all the new caps are in properly, so I'll see what happens after the tubes are tested.
BTW, I just picked up a Crosley 828 console, so I should be very busy learning and doing.

Thanks,
Eric

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Trouble getting started - by Eric Adams - 09-17-2012, 03:57 PM

RE: Trouble getting started - by Arran - 09-17-2012, 05:43 PM

RE: Trouble getting started - by Eric Adams - 09-17-2012, 06:07 PM

RE: Trouble getting started - by jerryhawthorne - 09-17-2012, 08:38 PM

RE: Trouble getting started - by Paul Philco322 - 09-17-2012, 08:52 PM

RE: Trouble getting started - by Eric Adams - 09-17-2012, 09:09 PM

RE: Trouble getting started - by Arran - 09-17-2012, 09:48 PM

RE: Trouble getting started - by jerryhawthorne - 09-30-2012, 12:48 AM

RE: Trouble getting started - by Eric Adams - 09-30-2012, 01:05 AM

RE: Trouble getting started - by jerryhawthorne - 09-30-2012, 03:00 AM

RE: Trouble getting started - by Eric Adams - 09-30-2012, 12:35 PM

RE: Trouble getting started - by Arran - 09-30-2012, 07:56 PM

RE: Trouble getting started - by Eric Adams - 09-30-2012, 11:00 PM

RE: Trouble getting started - by Arran - 09-30-2012, 11:57 PM

RE: Trouble getting started - by Eric Adams - 10-01-2012, 12:23 AM

RE: Trouble getting started - by Eric Adams - 10-01-2012, 07:41 PM

View a Printable Version

Users browsing this thread: 15 Guest(s)

Recent Posts
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM
Philco 60 Squealing
Your IF transformers are tuned to the resonant frequency they were designed for. When you observe the bell curve they di...RodB — 01:35 PM
identify very thin wire for replacement on 37-640
Thanks so much for your help! I really could not have gotten this far without the kindness of you and other members. T...georgetownjohn — 11:50 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me