38-15 Project

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-15 Project

ipwizard
Senior Member

Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio

#17

10-02-2012, 02:13 PM

I powered the set off my variac last night on 110v and after about 20-30 minutes the PT was at 113 degrees. I didnt get a chance to check for carbon traces on the band switch or the tube sockets yet maybe tonight.

I hope it's not a PT issue. It ohmed out fine when I first started this project.

Would it be worth it to unhook the secondaries of the PT and see if it still gets hot with no load?

-Keith

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-15 Project - by ipwizard - 08-10-2012, 01:25 PM

RE: 38-15 Project - by Chuck Schwark - 08-10-2012, 01:32 PM

RE: 38-15 Project - by codefox1 - 08-10-2012, 02:02 PM

RE: 38-15 Project - by Chuck Schwark - 08-10-2012, 03:22 PM

RE: 38-15 Project - by ipwizard - 08-10-2012, 04:40 PM

RE: 38-15 Project - by ipwizard - 08-13-2012, 01:05 AM

RE: 38-15 Project - by ipwizard - 09-30-2012, 12:39 AM

RE: 38-15 Project - by Ron Ramirez - 09-30-2012, 06:42 AM

RE: 38-15 Project - by TA Forbes - 09-30-2012, 08:32 AM

RE: 38-15 Project - by ipwizard - 09-30-2012, 12:46 PM

RE: 38-15 Project - by Arran - 09-30-2012, 08:41 PM

RE: 38-15 Project - by ipwizard - 10-01-2012, 01:12 PM

RE: 38-15 Project - by Chuck Schwark - 10-01-2012, 03:56 PM

RE: 38-15 Project - by ipwizard - 10-01-2012, 06:32 PM

RE: 38-15 Project - by Chuck Schwark - 10-02-2012, 08:58 AM

RE: 38-15 Project - by Ron Ramirez - 10-02-2012, 09:03 AM

RE: 38-15 Project - by ipwizard - 10-02-2012, 02:13 PM

RE: 38-15 Project - by Ron Ramirez - 10-02-2012, 02:23 PM

RE: 38-15 Project - by codefox1 - 10-02-2012, 02:24 PM

RE: 38-15 Project - by TA Forbes - 10-02-2012, 04:14 PM

RE: 38-15 Project - by LASJayhawk - 10-02-2012, 09:53 PM

RE: 38-15 Project - by ipwizard - 10-03-2012, 12:14 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4631 online users. [Complete List]
» 1 Member(s) | 4630 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me