philco model 29

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

philco model 29

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

#11

10-13-2012, 03:47 PM

Ok guy's,
Replaced 2 of the electrolitics with the proper value caps,and it now works like new.
The previous owner did a really nice jobe when he re-capped it.
Removed the circuit boards and did it right. Replaced the resistors too.
Very nice clean job.
Of course once I replaced the tuning condensor grommets and installed the chassis back in the cabinet, the bulb burned out for the shadow meter.
Haven't looked at it yet, but I think I can replace it without removing the chassis.
THink I will put it on CL tonight for a couple hundo's and see if anyone bites.
It was re-laquered quite a few years ago and still looks real nice.
Will be bring home a Grunow 835 and another Coronado 2CM tomorrow.
Again, thanks for the input.
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

philco model 29 - by murf - 10-04-2012, 10:20 PM

RE: philco model 29 - by Arran - 10-05-2012, 12:22 AM

RE: philco model 29 - by Ron Ramirez - 10-05-2012, 05:41 AM

RE: philco model 29 - by murf - 10-05-2012, 06:58 AM

RE: philco model 29 - by Glenn Roberts - 10-05-2012, 10:31 AM

RE: philco model 29 - by TA Forbes - 10-05-2012, 01:25 PM

RE: philco model 29 - by murf - 10-05-2012, 08:53 PM

RE: philco model 29 - by Ron Ramirez - 10-05-2012, 09:13 PM

RE: philco model 29 - by Steve Davis - 10-05-2012, 09:22 PM

RE: philco model 29 - by Arran - 10-05-2012, 10:01 PM

RE: philco model 29 - by murf - 10-13-2012, 03:47 PM

RE: philco model 29 - by murf - 10-13-2012, 03:55 PM

RE: philco model 29 - by Arran - 10-14-2012, 12:18 AM

RE: philco model 29 - by murf - 10-14-2012, 09:00 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5781 online users. [Complete List]
» 1 Member(s) | 5780 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me