Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philcos from New Zealand and Peru
#5

Yes, you're right, Arran. That early 1950s Tropic I have - a model 3010 - is rubber-stamped on the back of the chassis MADE IN CANADA. And, yes, it is a hot chassis. Icon_eek I bought a 51-532 just for the cabinet, to replace the broken but otherwise identical 3010 cabinet.

The Tropic you mention for sale was, I am sure, exported to the Caribbean when it was new but it was most likely not manufactured there.

Speaking of Canadian sets, there are a few Philcos that were made and sold in Canada that are identical to Tropic sets built in the USA and exported south. Sets such as the 35AT (41-712T), 39AT (41-722T), and the 55AT (42-760T). In fact I have a 39AT, I consider it part of my Tropic collection since it is identical to the 41-722T. I used to own a 55AT but later sold it.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philcos from New Zealand and Peru - by wa2ise - 10-13-2012, 08:53 PM
RE: Philcos from New Zealand and Peru - by Arran - 10-13-2012, 11:53 PM
RE: Philcos from New Zealand and Peru - by Arran - 10-14-2012, 08:26 PM
RE: Philcos from New Zealand and Peru - by Ron Ramirez - 10-14-2012, 08:45 PM
RE: Philcos from New Zealand and Peru - by Arran - 10-15-2012, 12:52 AM
RE: Philcos from New Zealand and Peru - by wa2ise - 10-15-2012, 10:07 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently no members online.

>