1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 16b-Measuring voltages
cwysong
Junior Member
**
Posts: 26
Threads: 6
Joined: Jan 2011
City: Bothell, WA
#1

10-27-2012, 07:51 PM
I have a 16b cathedral that has all the caps replaced, and it is playing fine. I am trying to do voltage measurements to see where things are at. My experience is mostly on Zenith radios where all voltages are measured to the chassis.
I see on the voltage chart that I measure P to K, SG to K, CG to K, and K to F. P to K voltages are pretty close. The others are nowhere close.
What is the way to measure Philco voltages?? I am using a Micronta with a 250K resistor in parallel to simulate the load.
I'm sure that this is a question that will become obvious to me once someone sheds some light on it.

Any help is appreciated!
Thanks
Chris
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 16b-Measuring voltages - by cwysong - 10-27-2012, 07:51 PM
RE: Philco 16b-Measuring voltages - by morzh - 10-27-2012, 11:50 PM
RE: Philco 16b-Measuring voltages - by cwysong - 10-28-2012, 10:39 AM
RE: Philco 16b-Measuring voltages - by morzh - 10-28-2012, 06:53 PM
RE: Philco 16b-Measuring voltages - by cwysong - 10-28-2012, 08:05 PM
RE: Philco 16b-Measuring voltages - by Arran - 10-28-2012, 08:38 PM
RE: Philco 16b-Measuring voltages - by TA Forbes - 10-28-2012, 09:19 PM
RE: Philco 16b-Measuring voltages - by cwysong - 10-28-2012, 09:43 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 5057 online users. [Complete List]
» 1 Member(s) | 5056 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration