1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 2 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Just got a model 90
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#6

10-30-2012, 09:54 AM
The liquid is borax and water. Not a hazzard.
Usually it's all leaked out over the years and leaves a white crust inside.

Drill a couple real small holes in the bottom to drain.
One to let the air in, one to drain. Seal again with a
dab of epoxy glue to the drill holes, unless you are
planning to surgically open the can and re-stuff,
then pull the guts and wash out the can and dry.

Chuck
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Just got a model 90 - by Groundhog74 - 10-25-2012, 08:37 PM
RE: Just got a model 90 - by TA Forbes - 10-25-2012, 08:40 PM
RE: Just got a model 90 - by Groundhog74 - 10-26-2012, 08:46 AM
RE: Just got a model 90 - by Groundhog74 - 10-30-2012, 06:46 AM
RE: Just got a model 90 - by Groundhog74 - 10-30-2012, 06:52 AM
RE: Just got a model 90 - by Chuck Schwark - 10-30-2012, 09:54 AM
RE: Just got a model 90 - by Groundhog74 - 10-31-2012, 06:13 AM
RE: Just got a model 90 - by jerryhawthorne - 10-31-2012, 09:31 PM
RE: Just got a model 90 - by Groundhog74 - 11-01-2012, 06:51 AM
RE: Just got a model 90 - by jerryhawthorne - 11-01-2012, 01:29 PM
RE: Just got a model 90 - by thirtiesradio - 11-08-2012, 01:56 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios