1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Tuning Static Philco 42-PT95
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#9

10-30-2012, 09:29 PM
No, no. B and C are the IF transformers. Do NOT touch those four alignment screws.

The two tuning gang trimmers are right there on top of the tuning assy - straight up on the stator brackets. See the two slotted screws?

[Image: http://www.philcorepairbench.com/images/trimmers.jpg]

If you sprayed on those, they need cleaning, ONLY if you sprayed them.
If not, do NOT touch them and only clean the tuning plates that you did spray. Hopefully this will help. Otherwise you need to take it to your local antique radio club meet and have it looked at.

Chuck
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Tuning Static Philco 42-PT95 - by winkydink - 10-25-2012, 10:11 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 10-25-2012, 10:27 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 09:54 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 12:54 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 01:11 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 04:38 PM
RE: Tuning Static Philco 42-PT95 - by Chuck Schwark - 10-30-2012, 09:29 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 09:35 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-31-2012, 08:56 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-31-2012, 09:21 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-08-2012, 02:19 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 11-08-2012, 02:36 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-08-2012, 02:45 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 11-08-2012, 07:00 PM
RE: Tuning Static Philco 42-PT95 - by morzh - 11-10-2012, 07:28 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-12-2012, 10:28 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3868 online users. [Complete List]
» 1 Member(s) | 3867 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration