1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Tuning Static Philco 42-PT95
winkydink
Member
***
Posts: 99
Threads: 24
Joined: Jan 2012
City: Cape May State, Province, Country: New Jersey
#13

10-31-2012, 09:21 AM
Chuck,

I agree about the local club aspect. Unfortunately I am in central PA and the closest clubs are in Harrisburg (2 hour drive) and Pittsburgh (3 hour drive), so no easy solution with regart to that. I will see how close I can get and possibly either farm it out or seek some advice over thanksgiving with some relatives.

Thanks again.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Tuning Static Philco 42-PT95 - by winkydink - 10-25-2012, 10:11 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 10-25-2012, 10:27 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 09:54 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 12:54 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 01:11 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 04:38 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-30-2012, 09:35 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-31-2012, 08:56 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 10-31-2012, 09:21 AM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-08-2012, 02:19 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 11-08-2012, 02:36 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-08-2012, 02:45 PM
RE: Tuning Static Philco 42-PT95 - by codefox1 - 11-08-2012, 07:00 PM
RE: Tuning Static Philco 42-PT95 - by morzh - 11-10-2012, 07:28 PM
RE: Tuning Static Philco 42-PT95 - by winkydink - 11-12-2012, 10:28 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3911 online users. [Complete List]
» 1 Member(s) | 3910 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration