Why not use....

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Why not use....

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

07-07-2007, 06:11 PM

You really should use the service info for the 46-1201 to service the 46-1201, and the 48-1201 schematic to service the 48-1201. As has been previously mentioned, there are differences between the two.

The PDF package I have available here at the Phorum (at http://www.philcoradio.com/phorum/showth...hp?tid=215) gives not only the basic service info for Model 46-1201, but also all of the factory updates and changes. This should get you through any 46-1201 service problem. And the price is right (FREE).

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Why not use.... - by diyahnih - 07-07-2007, 01:38 AM

[No subject] - by Carl Travis - 07-07-2007, 08:54 AM

46-1201 - by diyahnih - 07-07-2007, 04:43 PM

[No subject] - by Carl Travis - 07-07-2007, 05:58 PM

[No subject] - by Ron Ramirez - 07-07-2007, 06:11 PM

[No subject] - by Carl Travis - 07-08-2007, 08:41 AM

[No subject] - by Ron Ramirez - 07-08-2007, 11:17 AM

[No subject] - by Carl Travis - 07-08-2007, 12:50 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 3816 online users. [Complete List]
» 4 Member(s) | 3812 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me