1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
What type of caps to use?
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

11-21-2012, 06:11 PM
If you touch the yellow one with the tip of your iron GAME OVER it's shorted. I like the drops a bit better.
Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
What type of caps to use? - by Eric Adams - 11-21-2012, 11:42 AM
RE: What type of caps to use? - by Dave - 11-21-2012, 03:48 PM
RE: What type of caps to use? - by Eric Adams - 11-21-2012, 03:57 PM
RE: What type of caps to use? - by 7estatdef - 11-21-2012, 06:11 PM
RE: What type of caps to use? - by Eric Adams - 11-21-2012, 07:11 PM
RE: What type of caps to use? - by Conelrad - 11-22-2012, 03:34 AM
RE: What type of caps to use? - by DeckApe - 11-22-2012, 12:19 PM
RE: What type of caps to use? - by morzh - 11-22-2012, 11:23 PM
RE: What type of caps to use? - by TA Forbes - 11-23-2012, 01:08 PM
RE: What type of caps to use? - by LedHed - 11-23-2012, 01:48 PM
RE: What type of caps to use? - by codefox1 - 11-23-2012, 01:59 PM
RE: What type of caps to use? - by Eric Adams - 11-23-2012, 02:06 PM
RE: What type of caps to use? - by TA Forbes - 11-23-2012, 10:23 PM
RE: What type of caps to use? - by Eric Adams - 11-23-2012, 11:56 PM
RE: What type of caps to use? - by morzh - 11-24-2012, 07:07 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5626 online users. [Complete List]
» 1 Member(s) | 5625 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration