Philco Model 66 Repair

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco Model 66 Repair

radiola
Member

Posts: 64
Threads: 10
Joined: Dec 2010
City: Baltimore, MD

11-21-2012, 11:10 PM

I'm not using a signal generator, however, I can do that. The 6A7 (I'st detector/oscillator) does not respond to screwdriver, finger, or soldering iron. I've been lucky with coils in the past so I don't have a lot of experience with them, however, since there is a direct connection between the grid of the 6A7 and the oscillator, it looks like I should probably remove the oscillator coil by desoldering the lugs. All agree??
Once I do that, I don't really know what I would be looking for except for loose wiring?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco Model 66 Repair - by radiola - 11-21-2012, 12:43 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 06:07 PM

RE: Philco Model 66 Repair - by jph14 - 11-21-2012, 07:53 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 08:00 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 10:08 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-21-2012, 10:25 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 11:10 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-22-2012, 12:58 AM

RE: Philco Model 66 Repair - by radiola - 11-23-2012, 10:12 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 05:39 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 06:20 PM

RE: Philco Model 66 Repair - by jerryhawthorne - 11-25-2012, 09:30 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 10:48 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 11:21 PM

RE: Philco Model 66 Repair - by radiola - 11-26-2012, 10:01 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 12:16 AM

RE: Philco Model 66 Repair - by radiola - 11-27-2012, 01:12 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 11:20 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-27-2012, 11:47 PM

RE: Philco Model 66 Repair - by radiola - 11-28-2012, 12:34 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-28-2012, 11:32 PM

RE: Philco Model 66 Repair - by radiola - 11-29-2012, 02:21 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-29-2012, 10:30 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 02:32 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-30-2012, 06:54 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 11:30 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-01-2012, 06:51 PM

RE: Philco Model 66 Repair - by radiola - 12-02-2012, 10:41 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-02-2012, 10:53 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-04-2012, 11:00 PM

RE: Philco Model 66 Repair - by radiola - 12-05-2012, 12:52 AM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5605 online users. [Complete List]
» 1 Member(s) | 5604 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me