1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. #44" Need help"
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#9

11-28-2012, 06:04 PM
Thats good news on the .025 can. I'll follow your advice on restuffing the bakelite blocks. I did read an article on how to do that I believe at Philco repair bench. I've ordered a schematic from Mr. Schwark that should help me to see better than the little one I've been using. Have'nt cut or unsoldered anything yet just studying all info I can get and getting a plan together. Many notes and pictures first along with great advice from this forum gives me the confidence to get this project done right. Thanks
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 11:51 AM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 03:08 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 04:12 PM
RE: Philco Mod. #44" Need help" - by Steve Davis - 11-27-2012, 04:51 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 05:05 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 11:46 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 01:22 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-28-2012, 05:40 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 06:04 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-29-2012, 02:34 AM
RE: Philco Mod. #44" Need help" - by KCMike - 11-29-2012, 11:09 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 06:12 PM
RE: Philco Mod. #44" Need help" - by 7estatdef - 12-10-2012, 07:11 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 07:28 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-16-2012, 11:55 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-17-2012, 11:55 AM
RE: Philco Mod. #44" Need help" - by KCMike - 12-18-2012, 11:45 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-19-2012, 01:44 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 12-19-2012, 02:30 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-19-2012, 04:01 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-20-2012, 12:29 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 07:59 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 08:26 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 08:56 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 09:37 PM
RE: Philco Mod. #44" Need help" - by Ron Ramirez - 12-31-2012, 05:54 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-01-2013, 04:02 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 01-02-2013, 04:13 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-02-2013, 08:22 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-03-2013, 11:26 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5425 online users. [Complete List]
» 2 Member(s) | 5423 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration