Philco Model 66 Repair

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco Model 66 Repair

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#25

11-30-2012, 06:54 PM

Seems like the the primary of the 1st IF transformer is open. Check the resistance of the winding, should be 100 ohms or less. If it reads higher than that you'll to remove it and closely inspect the wiring to make sure that nothing is broken. Be careful as the wires are very small in gauge and break easily.
Terry

(This post was last modified: 11-30-2012, 06:56 PM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco Model 66 Repair - by radiola - 11-21-2012, 12:43 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 06:07 PM

RE: Philco Model 66 Repair - by jph14 - 11-21-2012, 07:53 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 08:00 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 10:08 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-21-2012, 10:25 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 11:10 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-22-2012, 12:58 AM

RE: Philco Model 66 Repair - by radiola - 11-23-2012, 10:12 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 05:39 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 06:20 PM

RE: Philco Model 66 Repair - by jerryhawthorne - 11-25-2012, 09:30 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 10:48 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 11:21 PM

RE: Philco Model 66 Repair - by radiola - 11-26-2012, 10:01 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 12:16 AM

RE: Philco Model 66 Repair - by radiola - 11-27-2012, 01:12 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 11:20 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-27-2012, 11:47 PM

RE: Philco Model 66 Repair - by radiola - 11-28-2012, 12:34 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-28-2012, 11:32 PM

RE: Philco Model 66 Repair - by radiola - 11-29-2012, 02:21 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-29-2012, 10:30 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 02:32 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-30-2012, 06:54 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 11:30 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-01-2012, 06:51 PM

RE: Philco Model 66 Repair - by radiola - 12-02-2012, 10:41 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-02-2012, 10:53 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-04-2012, 11:00 PM

RE: Philco Model 66 Repair - by radiola - 12-05-2012, 12:52 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5537 online users. [Complete List]
» 1 Member(s) | 5536 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me