1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Newbie Cap Question
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#9

12-02-2012, 08:50 PM
B+ supply supplies the voltage for the plates of the valves.

The metal box caps are a snap to open up and stuff, even compared to bakelites.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Newbie Cap Question - by TheGorper - 12-01-2012, 10:54 AM
RE: Newbie Cap Question - by codefox1 - 12-01-2012, 11:58 AM
RE: Newbie Cap Question - by TheGorper - 12-01-2012, 12:21 PM
RE: Newbie Cap Question - by TA Forbes - 12-01-2012, 08:40 PM
RE: Newbie Cap Question - by TheGorper - 12-01-2012, 11:16 PM
RE: Newbie Cap Question - by TheGorper - 12-01-2012, 11:50 PM
RE: Newbie Cap Question - by codefox1 - 12-02-2012, 01:17 PM
RE: Newbie Cap Question - by TheGorper - 12-02-2012, 08:44 PM
RE: Newbie Cap Question - by morzh - 12-02-2012, 08:50 PM
RE: Newbie Cap Question - by TheGorper - 12-02-2012, 08:52 PM
RE: Newbie Cap Question - by 7estatdef - 12-02-2012, 10:36 PM
RE: Newbie Cap Question - by 7estatdef - 12-02-2012, 10:58 PM
RE: Newbie Cap Question - by TheGorper - 12-02-2012, 11:02 PM
RE: Newbie Cap Question - by 7estatdef - 12-02-2012, 11:30 PM
RE: Newbie Cap Question - by TheGorper - 12-03-2012, 10:22 AM
RE: Newbie Cap Question - by TA Forbes - 12-03-2012, 10:43 AM
RE: Newbie Cap Question - by TheGorper - 12-16-2012, 02:43 PM
RE: Newbie Cap Question - by TheFightingHellfish - 01-14-2013, 11:56 PM
RE: Newbie Cap Question - by TA Forbes - 01-15-2013, 11:29 PM
RE: Newbie Cap Question - by TheGorper - 01-31-2013, 12:12 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4916 online users. [Complete List]
» 1 Member(s) | 4915 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration