Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-355
#1

Newcomer/lurker......found a Philco 42-355 in decent condition. There are some stains on the upper curved part of the veneer. Can these be removed without a lot of sanding? It has all the buttons but I will need the plastic panel the buttons project through. The screws are all there it's just the plastic got brittle and broke where it holds the panel on the wood. Looking for that.
Mike


Messages In This Thread
Philco 42-355 - by idaho181 - 12-04-2012, 03:28 PM
RE: Philco 42-355 - by Ron Ramirez - 12-04-2012, 04:52 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 04:57 PM
RE: Philco 42-355 - by Ron Ramirez - 12-04-2012, 05:00 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 05:24 PM
RE: Philco 42-355 - by jerryhawthorne - 12-04-2012, 08:17 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 08:33 PM
RE: Philco 42-355 - by jerryhawthorne - 12-04-2012, 10:12 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 12:55 PM
RE: Philco 42-355 - by DeckApe - 12-05-2012, 02:14 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 02:25 PM
RE: Philco 42-355 - by DeckApe - 12-05-2012, 05:10 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 05:52 PM
RE: Philco 42-355 - by TA Forbes - 12-05-2012, 06:34 PM
RE: Philco 42-355 - by jerryhawthorne - 12-05-2012, 06:54 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 03:08 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 03:22 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 03:31 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 05:01 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 05:11 PM
RE: Philco 42-355 - by Ron Ramirez - 12-06-2012, 05:13 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 05:31 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 06:26 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 09:58 PM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 12:33 AM
RE: Philco 42-355 - by jerryhawthorne - 12-07-2012, 02:09 AM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 12:20 PM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 12:30 PM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 12:32 PM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 12:49 PM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 12:55 PM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 02:12 PM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 02:29 PM
RE: Philco 42-355 - by jerryhawthorne - 12-07-2012, 02:47 PM



Users browsing this thread: 13 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM

[-]
Who's Online
There are currently no members online.

>