Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-355
#26

Well Mike, I couldn't do what you do either! Cows scare me a little, wheat is for bread. But I knew about as much about radios as I did about cows. The stuff is pretty simple if you can run a soldering iron and read a schematic (think of it as a road map), just different cities as you move along it. Quite satisfying when you do one. Bet you wish you had that old Zenith big dial radio.

Jerry

A friend in need is a pest!  Bill Slee ca 1970.


Messages In This Thread
Philco 42-355 - by idaho181 - 12-04-2012, 02:28 PM
RE: Philco 42-355 - by Ron Ramirez - 12-04-2012, 03:52 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 03:57 PM
RE: Philco 42-355 - by Ron Ramirez - 12-04-2012, 04:00 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 04:24 PM
RE: Philco 42-355 - by jerryhawthorne - 12-04-2012, 07:17 PM
RE: Philco 42-355 - by idaho181 - 12-04-2012, 07:33 PM
RE: Philco 42-355 - by jerryhawthorne - 12-04-2012, 09:12 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 11:55 AM
RE: Philco 42-355 - by DeckApe - 12-05-2012, 01:14 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 01:25 PM
RE: Philco 42-355 - by DeckApe - 12-05-2012, 04:10 PM
RE: Philco 42-355 - by idaho181 - 12-05-2012, 04:52 PM
RE: Philco 42-355 - by TA Forbes - 12-05-2012, 05:34 PM
RE: Philco 42-355 - by jerryhawthorne - 12-05-2012, 05:54 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 02:08 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 02:22 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 02:31 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 04:01 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 04:11 PM
RE: Philco 42-355 - by Ron Ramirez - 12-06-2012, 04:13 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 04:31 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 05:26 PM
RE: Philco 42-355 - by jerryhawthorne - 12-06-2012, 08:58 PM
RE: Philco 42-355 - by idaho181 - 12-06-2012, 11:33 PM
RE: Philco 42-355 - by jerryhawthorne - 12-07-2012, 01:09 AM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 11:20 AM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 11:30 AM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 11:32 AM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 11:49 AM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 11:55 AM
RE: Philco 42-355 - by idaho181 - 12-07-2012, 01:12 PM
RE: Philco 42-355 - by Ron Ramirez - 12-07-2012, 01:29 PM
RE: Philco 42-355 - by jerryhawthorne - 12-07-2012, 01:47 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>