1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. #44" Need help"
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#19

12-19-2012, 01:30 PM
I lik to recarb these old sets as most of the original resistors have drifted way up or turned themselves into theromstats that can drive you nuts. Makes a tremendous difference in performance and long term reliability, and costs so very little.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 10:51 AM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 02:08 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 03:12 PM
RE: Philco Mod. #44" Need help" - by Steve Davis - 11-27-2012, 03:51 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 04:05 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 10:46 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 12:22 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-28-2012, 04:40 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 05:04 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-29-2012, 01:34 AM
RE: Philco Mod. #44" Need help" - by KCMike - 11-29-2012, 10:09 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 05:12 PM
RE: Philco Mod. #44" Need help" - by 7estatdef - 12-10-2012, 06:11 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 06:28 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-16-2012, 10:55 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-17-2012, 10:55 AM
RE: Philco Mod. #44" Need help" - by KCMike - 12-18-2012, 10:45 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-19-2012, 12:44 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 12-19-2012, 01:30 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-19-2012, 03:01 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-20-2012, 11:29 AM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 06:59 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 07:26 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 07:56 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 08:37 PM
RE: Philco Mod. #44" Need help" - by Ron Ramirez - 12-31-2012, 04:54 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-01-2013, 03:02 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 01-02-2013, 03:13 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-02-2013, 07:22 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-03-2013, 10:26 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 4848 online users. [Complete List]
» 3 Member(s) | 4845 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration