1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Help with atwater kent model 82
OZ4
Senior Member
****
Posts: 285
Threads: 27
Joined: Nov 2012
City: Tehachapi. California
#10

12-19-2012, 03:25 PM
A quick update. I ordered a NOS 24 tube and tripled checked the resistors of all types with little success. So next is a NOS 35 tube. Sure wish I had access to a tube tester.

On a more positive note I did figure out how to get accurate voltage readings that jive with the riders chart. I just needed the right load. It took reviewing my old textbook on how meters work and the spec from the riders chart of 1000 ohms/volt. Now with a 250v scale that comes to 250k duh. Ok so I hung a 270k resistor on my digital meter as a dummy load and the readings were right on.
Chris
!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Help with atwater kent model 82 - by OZ4 - 11-24-2012, 03:13 PM
RE: Help with atwater kent model 82 - by codefox1 - 11-24-2012, 04:26 PM
RE: Help with atwater kent model 82 - by OZ4 - 11-24-2012, 05:39 PM
RE: Help with atwater kent model 82 - by OZ4 - 11-24-2012, 10:30 PM
RE: Help with atwater kent model 82 - by AI2V - 11-28-2012, 12:59 PM
RE: Help with atwater kent model 82 - by OZ4 - 12-19-2012, 03:25 PM
RE: Help with atwater kent model 82 - by Arran - 12-20-2012, 02:20 AM
RE: Help with atwater kent model 82 - by codefox1 - 12-20-2012, 05:45 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)