Zenith 7S363

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith 7S363

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

#19

12-26-2012, 02:08 PM

Hi guy's
I will be picking up 2 of these zeniths this weekend.
One has a decent finish, where the other needs re-finishing.
ANyone know if the multicored wood is done with veneer, or is it faux wood grain?
Probably need to replace that 6x5 tube with the 6x5gt?
I think that's the one that has caused problems with transformers in these?
Anyway, good luck with your restore, and let us know what problems you encounter.
These are very nice looking sets when restored.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith 7S363 - by LedHed - 02-01-2012, 09:13 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 02:08 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 03:13 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 03:46 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 05:34 PM

RE: Zenith 7S363 - by murf - 12-26-2012, 05:50 PM

RE: Zenith 7S363 - by LedHed - 12-26-2012, 06:07 PM

Re: Zenith 7S363 - by Jbaker - 02-02-2012, 10:38 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:14 AM

Re: Zenith 7S363 - by Jbaker - 02-03-2012, 12:27 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:43 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 08:36 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 09:30 AM

Re: Zenith 7S363 - by Eliot Ness - 02-03-2012, 10:08 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 10:27 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 11:41 AM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 11:44 AM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:29 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 12:53 PM

Re: Zenith 7S363 - by Michael Dennis - 02-03-2012, 01:01 PM

Re: Zenith 7S363 - by LedHed - 02-03-2012, 04:47 PM

Re: Zenith 7S363 - by Jbaker - 02-03-2012, 09:45 PM

Re: Zenith 7S363 - by LedHed - 02-14-2012, 01:30 PM

Re: Zenith 7S363 - by LedHed - 02-14-2012, 01:35 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4803 online users. [Complete List]
» 1 Member(s) | 4802 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me