1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Mod. #44" Need help"
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#36

01-02-2013, 11:52 PM
Mike, well we should assume and you know what that means that someone in the past has used that speaker on that radio. Now, if you have done your job of getting the major e-caps replaced and did a good visual as to what the earlier repair had done. I would just bring it up on the variac slowly and see what is going on. Who knows, it may start making some nice noise? I suspect that if the change over was done properly (again assuming) you might hear some nice music.

Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 11:51 AM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 03:08 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 04:12 PM
RE: Philco Mod. #44" Need help" - by Steve Davis - 11-27-2012, 04:51 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-27-2012, 05:05 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-27-2012, 11:46 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 01:22 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-28-2012, 05:40 PM
RE: Philco Mod. #44" Need help" - by KCMike - 11-28-2012, 06:04 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 11-29-2012, 02:34 AM
RE: Philco Mod. #44" Need help" - by KCMike - 11-29-2012, 11:09 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 06:12 PM
RE: Philco Mod. #44" Need help" - by 7estatdef - 12-10-2012, 07:11 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-10-2012, 07:28 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-16-2012, 11:55 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-17-2012, 11:55 AM
RE: Philco Mod. #44" Need help" - by KCMike - 12-18-2012, 11:45 PM
RE: Philco Mod. #44" Need help" - by TA Forbes - 12-19-2012, 01:44 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 12-19-2012, 02:30 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-19-2012, 04:01 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-20-2012, 12:29 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 07:59 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 08:26 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 08:56 PM
RE: Philco Mod. #44" Need help" - by KCMike - 12-22-2012, 09:37 PM
RE: Philco Mod. #44" Need help" - by Ron Ramirez - 12-31-2012, 05:54 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-01-2013, 04:02 PM
RE: Philco Mod. #44" Need help" - by codefox1 - 01-02-2013, 04:13 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-02-2013, 08:22 PM
RE: Philco Mod. #44" Need help" - by jerryhawthorne - 01-02-2013, 11:52 PM
RE: Philco Mod. #44" Need help" - by KCMike - 01-03-2013, 11:26 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4756 online users. [Complete List]
» 1 Member(s) | 4755 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration