41-220 Capacitor

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

41-220 Capacitor

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

01-03-2013, 04:46 PM

Hi Jim

Most likely you will be fine with a new 0.22 uF cap, without the coil. However, should you have any issues, it is easy enough to wind some 20 or 22 gauge wire around the new cap, replicating the direction and number of turns of wire on the original.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

41-220 Capacitor - by Jim Dutridge - 01-02-2013, 06:10 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-03-2013, 04:46 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-03-2013, 05:10 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-03-2013, 05:16 PM

RE: 41-220 Capacitor - by codefox1 - 01-03-2013, 11:37 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-05-2013, 11:51 AM

RE: 41-220 Capacitor - by exray - 01-06-2013, 07:37 AM

RE: 41-220 Capacitor - by codefox1 - 01-06-2013, 04:57 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-09-2013, 05:21 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-09-2013, 07:19 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-10-2013, 04:22 PM

RE: 41-220 Capacitor - by Ron Ramirez - 01-10-2013, 06:49 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-10-2013, 09:15 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-13-2013, 01:42 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-17-2013, 09:13 PM

RE: 41-220 Capacitor - by Arran - 01-17-2013, 10:39 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-18-2013, 06:24 PM

RE: 41-220 Capacitor - by Jim Dutridge - 01-19-2013, 10:59 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4868 online users. [Complete List]
» 1 Member(s) | 4867 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me